Видео

Do you know if this is the same for an A4 2012 ?

I see more your hands than what you was doing and you saying ha I will be right back you do more things that we can’t see I will give you a 2 for your not so good video

3.0 b6 👏 nobody has any videos on these cars 😭 thanks for this

It didn't work

Did you really clip that with one hand?? Mine is tight af... 😅

For all of those, this is not working: I needed to download the "CH340 driver" and after that the cable was recognized and not simply "USB serial" after that to change the port I had to normally double left click it to be able to set the port.(clocking right/properties did not give me an option to change the port) Hope this helps.

Damn bro you master P? favorite word is ahhh ……. Ahhhhh.. ahhh!😳

I just had this same oil leak. The o ring was hard as rock. My discovery was I found oil at the solenoid connector . Fixed now ,ty for video

Great tutorial and very clear instructions!

Use t20 torx. Be careful, the screws strip easily if not aligned properly. Also, the hinges pull down for easier mount.

Hey man it’s a long shot but I have the 74.5 belt and it is way too tight to get on, i know this video was posted forever ago but i can not get this belt on. I have rewatched and went step by step and can’t reach a goal.

Bro I tried this and my car wont accelerate

Clutch master pipe from reservior

Bro this legit fixed my screaming power steering pump. Saved a lot of time and frustration. Appreciate you

NEVER set an airbag face down, if it goes off it turns into a projectile.

thanks for the video helped me out alot i sub and liked the video

this is very helpful man. I have the same oil leak. I'm getting valve cover gasket and cam tensioner gasket replaced, I will have a look at this as well while I'm working on that area.

Be more professional and leave out the all cuss words !!!

Oring size 11x2 cheers

Hey buddy. R u sure that metal valve thing under the brake Reservoir tank is the clutch master cylinder? I was told its at the firewall above the clutch pedal is the clutch master cylinder. My clutch pressure is gone too. The biting point feels like its moved beyond the firewall... i only get a tiny bit of clutch pedal pressure travel wen im like an inch away from the firewall

What type of bolt is the one that goes to the mounting bracket?

Been there ... done that. Check Engine Light for secondary air improper flow. Replaced carboned-up combi, no more CEL, but SAI monitor refused to set. Replaced leaky solenoid vacuum control valve for the combi, monitor set in one 10 mile drive, passed California smog later that day.

i juss bought a 2004 audi a4 3.0 6speed . id love some maintenance tips .. as well as the oem paarts id need to get my engine bay looking like yours . pls help bro

Holy smokes, mate your video is helping people out even to this day. You quite possibly may have saved my glovebox and wallet 😂 thank you!

Hi there -- I know this video is pretty old now and the last comment was 3 years ago, but wanted to add my 2 cents: I ended up having to remove the bumper and put the radiator in service position to replace the tensioner pulley. When I went to put a new belt on, using a 19 mm wrench, I couldn't quite get a 74.5 inch belt over the top pulley because the wrench got in the way of fully compressing the tensioner. After spending on hour or so frustrated that I couldn't get the belt on, and not wanting to buy the $150 specialty tensioner tool, I came up with a solution: using a small c-clamp over the top of the tensioner release lever (and bottom of the clamp wedged under the top edge of the crankshaft pulley), I was able to tighten down enough on the clamp to compress the tensioner and get the belt on.

I have a 2004 Tdi a4 b6 Quattro with no lights no wipers no hazards radio works but have been told this could be ignition switch can you confirm this ?

So if I DONT have a laptop I can't reset the the light??? Didn't you say "AUTOZONE" CAN CLEAR THE LIGHT? THANKS

Hi, I buyed a cable that is the same as yours. When I plug into car it said interface found ecc.. but when I go to click an option like 06 instrument it try to find it but says “no response from controller” I’m trying it on a 2009 golf mk6 I hope u can help me

Awesome

I’m sad you cut out the most important part that’s why I came to this video lmao

Thank you Christopher for sharing this . I have this problem and I will check out my shocks ASAP.

This is the way

Change the Water Temp Sensor while you're at it (It lives underneath this valve) .cut my arms to pieces yesterday trying to do it without removing EGR and it's connecting pipes ;-)

Good video! I will reference it when I replace mine. Thanks for sharing!

Hi, I’m trying it today because on VCDS cable it said ( interface not found) but I appreciate your help I’ll see if works and you know. Thanks again

Take a look at this DIY. ruclips.net/video/1BazUF74s_k/видео.html

You dont have to take the cat off or the coolant hose

Perfect video thanks for making it great tip on draining the fluid!

Almost threw out my cable, but simply this was the issue. Thanks for sharing!

2011 Audi A4 ABS module has lost communication with the car. I have a used work in working order but it will need to be coded. The stock ones doesn't work and has my car in limp mode and disabled a ton of things. Sometimes you'll hear the stock one that's faulty clicking as if it's trying to work. Any ideas from anyone on what could be going on or can someone point me in the direction on how to code the new one so I can install it. Thanks in advance.

To test the valve, disconnect the small control vacuum hose and apply vacuum directly there with a hand vacuum pump.

It goes to your cluch master cylinder

I tried your solution. But it didnt fix the problem. It says this 01222 Active/Static Side airbag crash sensor, passenger side - G180 - open circuit I removed the clip under the chair. The yellow clip. And putted from the floor Blue to the blue Grey to the black. These colours were in this clip. But it Will not reset U got an clue whats wrong ? Can i send u picture from it ? Cheers

Thank you!!!

Do I need vcds to clear it once I do the fix?

Got it, but how to solve it if you locked the arm rest?

JP2GMD

Why the fuck wouldn’t you say what size wrench you use. God damn fucking idiot. Can’t believe you wouldn’t say that? I’m thinking people are strait up fucking retarded these days

Do u know the name of the bolt and spring that’s on the back of the flex pipe